Middle East and Africa
North America
Russia & CIS
South and Southeast Asia

E34 Compact Excavator

Specifications & Options


Close/Open all PDF version
Operating weight with cab and bucket (ISO 6016)
3,476 kg
Additional weight for steel tracks
94 kg
Transport mass (no attachment)
3,312 kg
Weight reduction with canopy
-118 kg
Additional weight for cab with HVAC
19 kg
Additional weight for long dipperstick
12 kg
Additional weight for heavy counterweight
291 kg
Ground pressure with rubber tracks
33.6 kPa
Bucket pivot angle
185 °
Maximum reach of working equipment
5,101 mm
Maximum reach of working equipment, long dipperstick
5,383 mm
Maximum reach at ground level
4,980 mm
Maximum reach at ground level, long dipperstick
5,270 mm
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted
2,017 mm
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted, long dipperstick
2,077 mm
Maximum blade height
382 mm
Maximum blade depth
456 mm
Maximum height of working equipment with dipperstick retracted
3,708 mm
Maximum bucket tooth height
4,804 mm
Maximum bucket tooth height, long dipperstick
4,985 mm
Maximum dump height
3,340 mm
Maximum dump height, long dipperstick
3,521 mm
Maximum depth of vertical wall which can be excavated
2,136 mm
Maximum depth of vertical wall which can be excavated, long dipperstick
2,414 mm
Maximum digging depth
3,117 mm
Maximum digging depth, long dipperstick
3,417 mm
(* Dentoes values which long dipperstick installed)
Blade height
322 mm
Clearance, upper structure to ground line
540 mm
Ground line to top of engine cover
1,557 mm
Length of track on ground
1,542 mm
Machine centre line to blade
1,528 mm
Minimum radius in travel position
3,787 mm
Overall length of track assembly
1,970 mm
Overall length in travel position
4,661 mm
Overall length in travel position, long dipperstick
4,761 mm
Track lug height
25 mm
Blade width
1,550 mm
2,468 mm
Track width
300 mm
Machine centre line to working equipment centre line, left-hand rotation
371 mm
Machine centre line to working equipment centre line, right-hand rotation
554 mm
Minimum turning radius
1,623 mm
Swing clearance, rear
1,125 mm
Swing clearance, rear (zero tail swing), long dipperstick
1,215 mm
Working width at maximum right-hand rotation
1,982 mm
Working width at maximum left-hand rotation
1,855 mm
Make / model
Kubota / D1703-E4B (Stage V)
Number of cylinders
1,642 cm3
Maximum power @ 2200 rpm (ISO 14396)
18.2 kW
Maximum torque (SAE)
97.4 Nm
Pump type
Single outlet variable displacement, load sensing torque pump with gear pumps
Total hydraulic capacity
101.2 L/min
Auxiliary (AUX1) flow
64 L/min
Auxiliary (AUX2) flow
20 L/min
Auxiliary (AUX1) relief
206 bar
Auxiliary (AUX2) relief
179 bar
Digging force, dipperstick (ISO 6015)
20,790 N
Digging force, long dipperstick (ISO 6015)
18,010 N
Digging force, bucket (ISO 6015)
33,430 N
Drawbar pull
34,132 N
Travel speed, low range
2.6 km/h
Travel speed, high range
4.7 km/h
Boom swing, left
75 °
Boom swing, right
55 °
Slew rate
8.6 RPM
Fuel reservoir
52 L
Hydraulic reservoir
8.3 L
Noise level LpA(EU Directive 2006/42/EC)
77 dB(A)
Noise level LWA(EU Directive 2000/14/EC)
94 dB(A)
Whole body vibration (ISO 2631–1)
0.1 ms-2
Hand-arm vibration (ISO 5349–1)
0.3 ms-2
  • 1550 mm dozer blade
  • 300 mm rubber tracks
  • Adjustable double acting auxiliary hydraulic (AUX1) with Quick Couplers
  • Battery disconnect switch
  • Blade float feature
  • Clamp ready
  • Control console locks
  • Cupholder
  • Dual Direction Detent
  • Engine/hydraulic monitor with shutdown
  • Foldable and ergonomic pedals
  • Full fuel warning alarm
  • Horn
  • Hydraulic joystick controls
  • Proportional fingertip auxiliary and boom swing offset hydraulic control
  • Retractable seat belt
  • Suspension seat with high back
  • Storage compartment
  • TOPS/ROPS/FOPS canopy * (1)
  • Two-speed travel with Auto shift
  • Upper structure four-point tie down
  • Water separator
  • Work light (boom)
  • Warranty: 24 months, 2000 hours (whichever occurs first)

(1) Roll Over Protective Structure (ROPS) – Meets requirements of ISO 3471. Tip Over Protective Structure (TOPS) – Meets requirements of ISO 12117. Falling Object Protective Structure (FOPS) - Meets requirements of ISO 3449.

  • Comfort package cab (Cloth susp. seat & Dlx displ.)
  • A-SAC package (Tilt coupler lines, Dlx displ.)
  • Object handling package (Valves, OWD, Lifteye)
  • Long dipperstick
  • Heavy counterweight
  • Steel tracks
  • AUX1 direct return to tank
  • AUX2 hydraulics
  • AUX1/AUX2/Drain on arm
  • Bucket valves (AUX3) kit
  • Hydr. coupler lines (AUX5)
  • Case drain line
  • Auto idle
  • Keyless ignition
  • Travel motion alarm
  • AM/FM MP3 radio
  • Additional halogen lights
  • LED lights set
  • Beacon
  • Special Application kit
  • L/R mirrors
  • Clamp w/ AUX1 valve
  • Klac D and MS03 coupler
  • Bobcat hydr. pin grabber
  • Grease Gun w/ holder

Certain specification(s) are based on engineering calculations and are not actual measurements. Specification(s) are provided for comparison purposes only and are subject to change without notice. Specification(s) for your individual Bobcat equipment will vary based on normal variations in design, manufacturing, operating conditions, and other factors.