Middle East and Africa
North America
Russia & CIS
South and Southeast Asia

Compact Excavators / E19 Compact Excavator

Specifications & Options


Close/Open All PDF version
Operating weight with cab and bucket (ISO 6016)
1,885 kg
Transport mass (no attachment)
1,768 kg
Weight reduction with canopy
-96 kg
Additional weight for long dipperstick
6 kg
Additional weight for counterweight
50 kg
Ground pressure with rubber tracks
32.4 kPa
Bucket pivot angle
196 °
Maximum reach of working equipment
4,084 mm
Maximum reach of working equipment, long dipperstick
4,257 mm
Maximum reach at ground level
4,039 mm
Maximum reach at ground level, long dipperstick
4,214 mm
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted
1,542 mm
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted, long dipperstick
1,561 mm
Maximum blade height
220 mm
Maximum blade depth
204 mm
Maximum height of working equipment with dipperstick retracted
2,564 mm
Maximum bucket tooth height
3,573 mm
Maximum bucket tooth height, long dipperstick
3,701 mm
Maximum dump height
2,566 mm
Maximum dump height, long dipperstick
2,693 mm
Maximum depth of vertical wall which can be excavated
1,948 mm
Maximum depth of vertical wall which can be excavated, long dipperstick
2,115 mm
Maximum digging depth
2,385 mm
Maximum digging depth, long dipperstick
2,565 mm
(* Dentoes values which long dipperstick installed)
Thu May 24 11:10:19 CEST 2018
Blade height
235 mm
Clearance, upper structure to ground line
419 mm
Ground line to top of engine cover
1,340 mm
Length of track on ground
1,114 mm
Machine centre line to blade
1,045 mm
Minimum radius in travel position
2,832 mm
Overall length of track assembly
1,476 mm
Overall length in travel position
3,831 mm
Overall length in travel position, long dipperstick
3,812 mm
Track lug height
25 mm
Blade width
980 mm
Blade width (extensions extended)
1,360 mm
2,299 mm
Track width
230 mm
Machine centre line to working equipment centre line, left-hand rotation
433 mm
Machine centre line to working equipment centre line, right-hand rotation
589 mm
Minimum turning radius
1,154 mm
Swing clearance, rear
1,009 mm
Working width at maximum right-hand rotation
1,801 mm
Working width at maximum left-hand rotation
1,645 mm
Make / model
Kubota / D722-E4B (Stage V)
Number of cylinders
719 cm3
Maximum power @ 2500 rpm (ISO 14396)
10.2 kW
Maximum torque (SAE)
43.5 Nm
Pump type
Dual piston pump with gear pump
Pump capacity
41.3 L/min
Piston pump capacity
30 L/min
Auxiliary (AUX1) flow
30 L/min
Auxiliary (AUX2) flow
15 L/min
Auxiliary (AUX1) relief
180 bar
Auxiliary (AUX2) relief
179 bar
Digging force, dipperstick (ISO 6015)
10,371 N
Digging force, long dipperstick (ISO 6015)
9,279 N
Digging force, bucket (ISO 6015)
20,835 N
Drawbar pull
19,380 N
Travel speed, low range
2.7 km/h
Travel speed, high range
4.2 km/h
Boom swing, left
80 °
Boom swing, right
60 °
Slew rate
8.4 RPM
Fuel reservoir
19 L
Hydraulic reservoir
14.3 L
Noise level LpA(EU Directive 2006/42/EC)
79 dB(A)
Noise level LWA(EU Directive 2000/14/EC)
93 dB(A)
Whole body vibration (ISO 2631–1)
0.1 ms-2
Hand-arm vibration (ISO 5349–1)
0.3 ms-2
  • 230 mm rubber track
  • 980 mm dozer blade with two 190 mm blade extensions
  • Battery disconnect switch
  • Control console locks
  • Cupholders
  • Double acting auxiliary hydraulics with quick couplers
  • Engine monitor with auto shutdown
  • Exposed counterweight with 4 mm steel tailgate
  • Foldable and ergonomic travel pedals
  • Full fuel warning alarm
  • Horn
  • Hydraulic and travel control lockout
  • Hydraulic joystick controls
  • Hydraulically retractable undercarriage from 1360 mm to 980 mm
  • Retractable seat belt
  • Storage compartment
  • TOPS/ROPS/FOPS canopy (1)
  • Two-speed travel
  • Upper structure four point tie down
  • Water separator
  • Work light (boom)
  • Warranty: 24 months, 2000 hours (whichever occurs first)

(1) Roll Over Protective Structure (ROPS) – Meets requirements of ISO 3471. Tip Over Protective Structure (TOPS) – Meets requirements of ISO 12117. Falling Object Protective Structure (FOPS) - Meets requirements of ISO 3449.

  • Demolition package (boom, arm, bucket cylinder covers & HD travel hoses guard)
  • Object handling package (Valves, OWD, Lifteye)
  • TOPS/ROPS/FOPS cab w/ heater
  • Long dipperstick w/ clamp eyes
  • Long dozer blade
  • AUX1 direct return to tank
  • AUX2 hydraulics
  • AUX1/AUX2 on arm
  • Keyless ignition
  • Travel motion alarm
  • AM/FM MP3 radio
  • Additional halogen lights
  • LED lights set
  • Beacon
  • Special Application kit
  • L/R mirrors
  • Fire extinguisher
  • Hydraulic clamp
  • Klac C and MS01 couplers
  • Comfort package (Superior seat for canopy or Cloth susp. seat for cab, Autospeed shift, Aux and Off-set pilot control)
  • Performance package (HD travel motors, add. counterweight)
  • Grease Gun w/ holder

Certain specification(s) are based on engineering calculations and are not actual measurements. Specification(s) are provided for comparison purposes only and are subject to change without notice. Specification(s) for your individual Bobcat equipment will vary based on normal variations in design, manufacturing, operating conditions, and other factors.