Middle East and Africa
North America
Russia & CIS
South and Southeast Asia

E26 Compact Excavator

Specifications & Options


Close/Open all PDF version
Operating weight with cab and bucket (ISO 6016)
2,608 kg
Transport mass (no attachment)
2,477 kg
Weight reduction with canopy
-118 kg
Ground pressure with rubber tracks
30.3 kPa
Bucket pivot angle
185 °
Maximum reach of working equipment
4,542 mm
Maximum reach at ground level
4,413 mm
Maximum working equipment radius with boom at maximum height and dipperstick fully retracted
2,052 mm
Maximum blade height
385 mm
Maximum blade depth
420 mm
Maximum height of working equipment with dipperstick retracted
3,104 mm
Maximum bucket tooth height
4,006 mm
Maximum dump height
2,845 mm
Maximum depth of vertical wall which can be excavated
1,474 mm
Maximum digging depth
2,568 mm
(* Dentoes values which long dipperstick installed)
Blade height
319 mm
Clearance, upper structure to ground line
539 mm
Ground line to top of engine cover
1,540 mm
Length of track on ground
1,543 mm
Machine centre line to blade
1,462 mm
Minimum radius in travel position
3,192 mm
Overall length of track assembly
1,965 mm
Overall length in travel position
4,174 mm
Track lug height
21 mm
Blade width
1,500 mm
2,438 mm
Track width
250 mm
Machine centre line to working equipment centre line, left-hand rotation
580 mm
Machine centre line to working equipment centre line, right-hand rotation
705 mm
Minimum turning radius
1,755 mm
Swing clearance, rear
820 mm
Working width at maximum right-hand rotation
1,741 mm
Working width at maximum left-hand rotation
1,616 mm
Make / model
Kubota / D1105-E4B (Stage V)
Number of cylinders
1,123 cm3
Maximum power @ 2400 rpm (ISO 14396)
15.4 kW
Maximum torque (SAE)
71.2 Nm
Pump type
Dual outlet variable displacement piston pump with gear pumps
Total hydraulic capacity
87 L/min
Auxiliary (AUX1) flow
50 L/min
Auxiliary (AUX2) flow
20 L/min
Auxiliary (AUX1) relief
180 bar
Auxiliary (AUX2) relief
179 bar
Digging force, dipperstick (ISO 6015)
15,690 N
Digging force, bucket (ISO 6015)
23,720 N
Drawbar pull
29,080 N
Travel speed, low range
2.5 km/h
Travel speed, high range
4.3 km/h
Boom swing, left
60 °
Boom swing, right
60 °
Slew rate
9.3 RPM
Fuel reservoir
34.4 L
Hydraulic reservoir
10.2 L
Noise level LpA(EU Directive 2006/42/EC)
80 dB(A)
Noise level LWA(EU Directive 2000/14/EC)
93 dB(A)
Whole body vibration (ISO 2631–1)
0.1 ms-2
Hand-arm vibration (ISO 5349–1)
0.5 ms-2
  • 1500 mm dozer blade
  • 250 mm rubber track
  • Adjustable double acting auxiliary hydraulic (AUX1) with Quick Couplers
  • Battery disconnect switch
  • Blade float feature
  • Control console locks
  • Cupholder
  • Dual Direction Detent
  • Engine/hydraulic monitor with shutdown
  • Foldable and ergonomic travel pedals
  • Full fuel warning alarm
  • Horn
  • Proportional fingertip auxiliary and boom swing offset hydraulic control
  • Retractable seat belt
  • Seat with high back
  • Storage compartment
  • TOPS/ROPS/FOPS canopy * (1)
  • Two-speed travel with Auto shift
  • Upper structure four-point tie down
  • Work light (boom)
  • Water separator
  • Warranty: 24 months, 2000 hours (whichever occurs first)

(1) Roll Over Protective Structure (ROPS) – Meets requirements of ISO 3471. Tip Over Protective Structure (TOPS) – Meets requirements of ISO 12117. Falling Object Protective Structure (FOPS) - Meets requirements of ISO 3449.

  • Object handling package (Valves, OWD, Lifteye)
  • AUX1 direct return to tank
  • AUX2 hydraulics
  • AUX1/AUX2/Drain on arm
  • Case drain line
  • Auto idle
  • Keyless ignition
  • Travel motion alarm
  • AM/FM MP3 radio
  • Additional halogen lights
  • Beacon
  • Dlx textile suspension seat
  • Special Application kit
  • L/R mirrors
  • Klac D and MS03 coupler
  • Grease Gun w/ holder

Certain specification(s) are based on engineering calculations and are not actual measurements. Specification(s) are provided for comparison purposes only and are subject to change without notice. Specification(s) for your individual Bobcat equipment will vary based on normal variations in design, manufacturing, operating conditions, and other factors.